PBDD Piggyback Disconnects
PBDD piggyback disconnects combine a female receptacle with an additional male tab. They allow a second matching female connector to share a connection point without putting two wires into a single crimp barrel.
Built around your connection.
- Conductor range
- 0.5–6 mm²
- Conductor
- Copper wire
- Contact material
- Brass
- Insulation
- PVC
- Connection
- Disconnect
- Variants
- 3
Selection essentials
The extra tab is a branch point. The combined branch current must stay within the lowest-rated component and conductor in the circuit.
Typical applications
Appliance wiring, control equipment and components fitted with matching flat-tab connections.
PBDD dimensions & wire sizes.
Read the dimensions before selecting.
The extra tab is a branch point. The combined branch current must stay within the lowest-rated component and conductor in the circuit.
All dimensional columns are in millimetres. Conductor sizes are cross-sectional areas, not wire diameters. The first column contains the complete ordering code.
3 model variants
| Model | Wire mm² | AWG | Color | Imax A | Tab t × w mm | B mm | F mm | H mm | D mm | Bore d mm | L mm |
|---|---|---|---|---|---|---|---|---|---|---|---|
| PBDD1.25-250 | 0.5–1.5 | 22–16 | Red | 10 | 0.8×6.35 | 7.4 | 6.3 | 10.6 | 3.8 | 1.7 | 21 |
| PBDD2-250 | 1.5–2.5 | 16–14 | Blue | 15 | 0.8×6.35 | 7.7 | 6.3 | 10.6 | 4.3 | 2.3 | 21 |
| PBDD5.5-250 | 4–6 | 12–10 | Yellow | 24 | 0.8×6.35 | 7.7 | 6.3 | 13.5 | 5.7 | 3.4 | 23.5 |
No models match. Clear the search or select another conductor size.
Dimensions are nominal and stated in millimetres. Select by conductor cross-section and the actual mating dimensions, not by color alone.
AWG and kcmil values are size references, not exact conversions of every metric cross-section.
Imax is the terminal size reference limit. The permissible circuit current also depends on wire size, ambient temperature, crimp quality and the mating terminal; use the lowest applicable limit.
A suitable terminal needs a suitable crimp.
Use the stated copper conductor size. Match the stud, slot, tab, tube or pin dimensions to the receiving component.
Strip the wire to the metal barrel or tube insertion length. Keep all strands intact and inside the barrel.
Use a die intended for this terminal construction and the selected wire size. Complete the tool’s crimp cycle.
Check strand capture, barrel deformation and retention. Install to the receiving component’s tightening and clearance requirements.
PBDD questions answered.
What is the PBDD series used for?
PBDD piggyback disconnects combine a female receptacle with an additional male tab. They allow a second matching female connector to share a connection point without putting two wires into a single crimp barrel.
How do I choose a PBDD model?
The extra tab is a branch point. The combined branch current must stay within the lowest-rated component and conductor in the circuit.
Can I select the terminal by insulation color alone?
No. Match the conductor cross-section and the mating geometry first. Colors identify size families within a product system; ferrule color conventions differ between German and French systems.
How should the terminal be crimped?
Strip to the metal barrel or tube insertion length without cutting strands. Insert the conductor fully, use a die made for the terminal type and wire size, complete the crimp, then inspect strand capture and mechanical retention. Follow the receiving component’s tightening instructions.
Does full insulation make a disconnect waterproof?
No. An insulating sleeve covers conductive parts but is not a sealed housing. Use an enclosure or a specified sealed connector where moisture protection is required.
Related terminal families.
Specify your PBDD models.
Send the complete model codes, quantities, conductor sizes and destination country.