Компания Wenzhou Changsong Electric Co., Ltd.
Каталоги и технические файлыКонтакты и запросыWhatsApp
CHSOИНДУСТРИАЛЬНАЯ ЭЛЕКТРОНИКАЗапросите предложение 0→
Aluminium lugs

DIN DL Aluminium Cable Lugs — AU Series

Aluminium ring lugs with AU size designations, covering 16–300 mm². The dimensional table links the conductor bore to stud-hole and barrel-length requirements.

16–300 mm²AluminiumBolted palm
DIN DL Aluminium Cable Lugs — AU Series
DIN DL / AU · Aluminium lugs
Технические данные

Material, connection & construction

DIN DL / AU product specifications
ПараметрСпецификация
СерияDIN DL / AU
Product formDIN DL Aluminium Cable Lugs — AU Series
Conductor / interfaceAluminium conductor to aluminium-compatible equipment terminal
Body materialAluminium
Size range16–300 mm²
Connection methodCrimped barrel with bolted palm
InsulationNon-insulated; provide application-specific joint insulation and enclosure protection
РазмерыMillimetres; conductor cross-section in mm²
Выбор модели

Модели и размеры

All dimensional values are in millimetres. Conductor sizes are in mm². Use the symbols in the drawing for the selected construction.

Use the AU model code for ordering. DIN DL identifies the product family rather than a separate third-party certification.

DIN DL Aluminium Cable Lugs — AU Series construction
Product construction
DIN DL Aluminium Cable Lugs — AU Series dimension symbols
Dimensional geometry · All dimensions in mm
Use the dimension symbols in this series drawing; symbols can differ between constructions.

DIN DL / AU model dimensions
МодельStud hole ØBarrel ID dOverall length LBarrel length L1
AU-168.45.86029
AU-2510.56.862.529
AU-3510.587741
AU-5010.59.878.542
AU-7010.511.28551
AU-951313.29055
AU-1201314.79655
AU-1501316.310659
AU-1851318.310859
AU-240172112469
AU-3001723.312569
Заявка и установка

Select the complete connection

Подходит для применения

  • Aluminium feeder terminations in distribution equipment
  • Bolted connections with an aluminium-compatible contact interface
  • Replacement lugs selected by bore, palm and mounting geometry

Список заказанных товаров

Specify DIN DL / AU construction, conductor material and nominal section, conductor strand class, stud-hole diameter, palm clearance, tool/die system, quantity and required finish.

Последовательность установки

  1. Isolate the circuit and verify that it is de-energised. Identify the conductor material, section and strand construction.
  2. Select the matching connector, tool and die combination. Strip to the required insertion length without cutting or losing strands.
  3. Prepare the aluminium contact surface and apply the joint compound specified by the connection system. Keep compound and preparation appropriate to each metal.
  4. Insert the conductor fully and crimp in the sequence and number of compressions specified for the connector/tool system. Do not substitute a die solely because its size marking looks similar.
  5. Place the palm flat against the intended terminal, use matching hardware and tighten to the equipment connection specification. Support the cable so the palm carries no avoidable bending load.
  6. Inspect the compression, conductor retention and contact alignment. Restore suitable insulation and protection, then carry out the assembly checks before energising.
Практические ответы

Часто задаваемые вопросы

What distinguishes DIN DL / AU from other cable connectors?

Aluminium ring lugs with AU size designations, covering 16–300 mm². The dimensional table links the conductor bore to stud-hole and barrel-length requirements.

How do I select the correct DIN DL / AU size?

Specify DIN DL / AU construction, conductor material and nominal section, conductor strand class, stud-hole diameter, palm clearance, tool/die system, quantity and required finish.

What should I check before ordering this series?

Use the AU model code for ordering. DIN DL identifies the product family rather than a separate third-party certification.

Does the conductor size determine a universal current rating?

No. Connection current depends on the cable material and size, insulation temperature, terminal interface, installation conditions and verified crimp system. Select the whole circuit and connection together.

Can I use any crimping die with the same size number?

No. Die profile, tool force, connector wall thickness and conductor construction work as a system. Use the specified tool/die combination for the chosen connector.

Is the model size the same as the stud-hole diameter?

No. The conductor size identifies the cable section, while the hole dimension identifies the bolted interface. Both must suit the application.

Запросы от дистрибьюторов и монтажных компаний

Specify the conductor.
Match the connection.

Include DIN DL / AU model and construction, conductor material and size, stud-hole or joint requirements, quantities and packaging needs.

Запрос на цену ↗
WhatsApp